Front brake adjustment

The brake can be adjusted by simply adjusting the free play of the brake lever. The piston in the caliper moves forward as the brake pad wears out, automatically adjusting the clearance between the brake pads and brake disc.

CAUTION: Proper lever free play is essential to avoid excessive brake drag.

The free play at the end of the front brake lever should be 5 — 8 mm (0.2 — 0.3 in).

1.      Loosen the lock nut.

2.      Turn the adjuster so that the brake lever movement at the lever end is 5 - 8 mm (0.2 - 0.3 in) before the adjuster contacts the master cylinder piston.

3.      After adjusting, tighten the lock nut

WARNING: Check the brake lever free play. Be sure the brake is working properly.

1 Adjuster 2. Lock nut a. 5 — 8 mm (0.2 — 0.3 in)

Rear brake pedal position adjustment

The brake pedal top end should be 27 - 33 mm (1.1 - 1.3 in) below the top of the footrest.

1.      Remove the brake pedal pinch bolt and remove the brake pedal.

2.      The punched mark on the brake pedal shaft and the punched mark on the brake pedal which must be aligned to install the brake pedal.

3.      Install the brake pedal pinch bolt securely.

1. Pinch bolt 2 Punched marks a. 27 — 33 mm (1.1 —1.3 in)

Rear brake adjustment

The brake pedal free play is set at the factory. This free play ranges from where the brake pedal is trod to where the brake begins to take effect. No adjustment is necessary.

Free play: 20 - 30 mm (0.8 — 1.2 in)

a. 20 - 30 mm {0.8 -1.2 in)

Front and rear brake pad check

A wear indicator is attached to each brake pad to facilitate disc brake pad checks. This indicator permits a visual check without disassembling the pads. To check, look at the pad wear indicator in back of the caliper. If any pad is worn to the wear limit, replace both pads in the caliper.

FRONT

1. Wear indicator

REAR

1 Wear indicator

Inspecting the brake fluid level

Insufficient brake fluid may allow air to enter the brake system, possibly causing the brake to become ineffective. Check the brake fluid level and replenish when necessary observing these precautions:

FRONT

1. Lower level

REAR

1. Lower level

1. Use only the designated quality brake fluid; otherwise, the rubber seals may deteriorate, causing leakage and poor brake performance.

Recommended brake fluid: DOT #3

2.      Refill with the same type and brand of brake fluid; mixing fluids may result in a harmful chemical reaction and lead to poor performance.

3.      Be careful that water or other contamination does not enter the master cylinder when refilling. Water will significantly lower the boiling point and may result in vapor lock.

4.      Brake fluid may erode painted surfaces or plastic parts. Always clean up spilled fluid immediately.

Brake fluid replacement

1.      Complete fluid replacement should be done whenever the caliper cylinder or master cylinder is disassembled, or the fluid becomes seriously contaminated.

2.      Replace the following components whenever damaged or leaking.

a.    Replace all brake seals every two years.

b.    Replace all brake hoses every four years.

c.    Replace the plunger kits every two years.

Brake light switch adjustment

The brake light switch is operated by movement of the brake pedal. To adjust, hold the main body of the switch with your hand so it does not rotate and turn the adjusting nut. Proper adjustment is achieved when the brake light comes on just before the brake begins to take effect.

1. Main body 2. Adjusting nut

Clutch adjustment

This model has two clutch cable length adjusters. The cable length adjusters are used to take up slack from cable stretch and to provide sufficient free play for proper clutch operation. Normally, once the clutch cable length adjuster (crankcase) is properly set; the only adjustment required is maintenance of free play at the clutch cable length adjuster (handlebar lever).

1.      Loosen either the handlebar lever adjuster lock nut or the cable length adjuster lock nut.

2.      Turn the cable length adjuster either in or out until proper lever free play is achieved.

Clutch lever free play: 2 —3 mm (0.08 —0.12 in)

1. Lock nut 2. Adjuster

1. Lock nut 2. Adjuster a. 2 - 3 mm (008 — 0.12 in)

Handlebars adjustment

1. Vertical adjustment

Five-stage adjustment is possible. a. Remove the cap and loosen the grip bar installation bolt.

1. Grip bar bolt

b. Loosen the grip bar and turn and align the adjusting collar either clockwise or counterclockwise. To adjust turn the collar counterclockwise to raise the grip ban turn the collar clockwise to lower the gip bar. (The red mark indicates the standard position.)

NOTE: Check to see that the projection on the handlebar fits a notch in the collar.

2. Horizontal adjustment

Four-stage adjustment is possible. a. Remove the cap and loosen the handlebar installation bolt.

1. Handlebar bolt

b. Loosen the handlebar and turn and align the adjusting collar either clockwise or counterclockwise. To adjust, turn the collar counterclockwise to move the handlebar inward, turn the collar clockwise to move the handlebar outward. (The red make indicates the standard position.)

NOTE: Check to see that the projection on the handlebar fits a notch in the collar.

ELECTRICAL

Battery

1. The fluid level should be between the upper and lower level marks. Use only distillod water if refilling is necessary.

CAUTION: Normal tap water contains minerals which are harmful to a battery; therefore, refill only with distilled water.

2. Always make sure the connections are correct when installing the battery. Make sure the breather pipe is properly connected, properly routed, and is not damaged or obstructed.

CAUTION: The battery must be charged before using to insure maximum performance. Failure to properly charge the battery before first use, or low electrolyte level will cause premature failure of the battery. Charging current: 1.4 amps/10 hrs or until the specific gravity reaches 1.280 at 20°C (68°F)

WARNING: Battery electrolyte is poisonous and dangerous, causing severe burns, etc. It contains sulfuric acid. Avoid contact with skin, eyes or clothing.

Antidote: EXTERNAL-Flush with water. INTERNAL-Drink large quantities of water or milk. Follow with milk of magnesia, beaten egg, or vegetable oil. Call physician immediately.

Eyes: Flush with water for 15 minutes and get prompt medical attention. Batteries produce explosive gasive gases. Keep sparks, flame, cigarettes, etc. away. Ventilate when charging or using in closed space. Always shield eyes when working near batteries. KEEP OUT OF REACH OF CHILDREN.

Spark plug

1.      Check the electrode condition and wear, insulator color and electrode gap.

2.      Use a wire gauge for measuring the plug gap.

3.      If the electrodes become too worn, replace the spark plug.

4.      When installing the plug, always clean the gasket surface. Wipe off any grime that might be present on the surface of the spark plug, and torque the spark plug properly.

Standard spark plug:

BPR8ES (NGK) Spark plug gap:

0.7 - 0.8 mm (0.028 ~ 0.032 in) Spark plug tightening torque:

20 Nm (2.0 mkg, 14 fMb)

Replacing the headlight bulb

This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace the bulb as follows: 1. Remove the 2 screws holding the light unit assembly to the headlight body.

2.      Disconnect the leads, and remove the light unit assembly.

3.      Turn the bulb holder couterclockwise and remove the defective bulb.

WARNING: Keep flammable products or your hands away from the bulb while it is on, it will be hot. Do not touch the bulb until it cools down.

4. Slip a new bulb into position and secure it in place with the bulb holder.

CAUTION: Avoid touching the glass part of the bulb. Keep it free from oil; otherwise, the transparency of the glass, life of the bulb, and illuminous flux will be adversely affected. If oil gets on the bulb, throughly clean it with a cloth moistened with alcohol or lacquer thinner.

1. Don't touch

5. Reinstall the light unit assembly to the headlight body. Adjust the headlight beam if necessary.

Headlight beam adjustment

1.      Horizontal adjustment:

To adjust the beam to the left, turn the adjusting screw clockwise. To adjust the beam to the right turn the screw counterclockwise.

2.      Vertical adjustment:

To raise the beam, turn the adjusting screw clockwise.

To lower the beam, turn the screw counterclockwise.

1. Horizontal adjusting screw 2. Vertical adjusting screw

Fuse replacement

1.      The fuse block is located under the seat.

2.      If any fuse is blown, turn off the ignition switch and the switch in the circuit in question, install a new fuse of proper amperage.

Turn on the switches, and see if the electrical device operates. If the fuse immediately blows again, find the cause in the circuit in question.

1. Main fuse 2. Spare fuse

WARNING: Do not use fuses of a higher amperage rating than those recommended. Substitution of a fuse of improper rating can cause extensive electrical system damage and possible fire.

Generator brushes replacement

The generator carbon brushes require periodical replacement.

1.      Remove the generator cover screws and the left side generator cover.

2.      Remove the screws and separate the brushes assembly from the cover.

3. Remove the panhead screws and replace the old brushes to new ones.

Fuel petcock cleaning

1.      Turn the fuel petcock lever to the "RES". Remove the fuel pipe from the fuel petcock.

2.      Remove the seat, the fuel tank clamp, and the fuel-tank-retainer plate.

3.      Lift the tank and remove the drain cover and clean it with solvent. If gasket is damaged, replace.

1. Drain cover

Fuel petcock disassembly

If the fuel petcock is leaking or excessively contaminated, it should be removed from the fuel tank and inspected.

1.      Remove the fuel tank and position it so that fuel will not spill when the cock is removed.

2.      Remove the petcock and inspect the filter screen. Replace the filter if seriously contaminated.

3.      Remove the screws on front and rear of the petcock and remove the plate, gaskets, lever, and diaphragm.

4.      Inspect all components and replace any that are damaged. If the diaphragm is in any way damaged, or the petcock body gasket surfaces scratched or corroded, the petcock assembly must be replaced. If there is abrasive damage to any component, the fuel tank must be drained and flushed.

5.      Reassemble the petcock and install it on the fuel tank.

Cable inspection and lubrication

WARNING: Damage to the outer housing of the various cables, may cause corrosion and often free movement will be obstructed. An unsafe condition may result so replace such cables as soon as possible.

Lubricate the inner cable and cable end. If they do not operate smoothly, replace them.

Recommended lubricant: SAE 10W30 motor oil

Throttle cable and grip lubrication

The throttle twist grip assembly should be greased when the cable is lubricated, since the grip must be removed to get at the end of the throttle cable. Two screws clamp the throttle housing to the handlebar. Once these two are removed, the end of the cable can be held high to pour in several drops of lubricant. With the throttle grip disassembled, coat the metal surface of the grip assembly with a suitable all-purpose grease to cut down friction.

Rear arm pivot bearings

The swing arm must pivot freely on its bearings but not have any excess play. Check and adjust pivot bearings if necessary. (Refer to CHAPTER 5. SWING ARM).

Brake and change pedals/brake and clutch levers

Lubricate the pivoting parts of each lever and pedal.

Recommended lubricants: SAE 10W30 motor oil

Center and side stand pivots

Lubricate the center and side stands at their pivot points.

Recommended lubricants: SAE 10W30 motor oil

Steering head adjustment

1. Raise the front end of the motorcycle so that there is no weight on the front wheel.

WARNING: Securely support the motorcycle so there is no danger of it falling over.

2. Grasp the bottom of the forks and gently rock the fork assembly backward and forward, checking for looseness in the steering assembly bearings.

3. If there is looseness in the steering head, loosen the steering fitting bolt

1. Steering fitting bolt 2. Steering fitting nut

4. Use steering nut wrench to loosen top steering fitting nut. The top nut serves as a lock nut.

1. Steering nut wrench

5.      Tighten the lower steering fitting nut until the steering head is tight but does not bind when forks are turned.

6.      Retighten the top steering fitting nut and steering fitting bolt.

7.      Recheck steering adjustment to make sure there is no binding when the forks are moved from lock to lock. If necessary, repeat adjustment procedure.

Front fork oil change

WARNING.

1.      Fork oil leakage can cause loss of stability and safe handling. Have any problem corrected before operating the motorcycle.

2.      Securely support the motorcycle so there is no danger of it falling over.

1.      Elevate the front wheel by placing a suitable stand under the engine.

2.      Remove the rubber cap from the top of each fork.

3.      Remove the air valve cap from the left fork.

4.      Keep the valve open by pressing it for several seconds so that the air can be let out of the inner tube.

1. Air valve cap

5. Loosen the front fork pinch bolts and remove the cap bolts from the inner fork tubes.

1. Pinch bolt 2. Cap bolt

6. Place an open container under each drain hole. Remove the drain screw from each outer tube.

WARNING:

Do not let oil contact the disc brake components. If any oil should contact the brake components, it must be removed before the motorcycle is operated. Oil will cause diminished braking capacity and will damage the rubber components of the brake assembly.

1. Drain screw

7.      After most of the oil has drained, slowly pump the forks up and down to remove any remaining oil.

8.      Inspect the drain screw gasket. Replace if damaged. Reinstall the drain screws.

9.      Pour the specified amout of oil into each the fork inner tube.

Front fork oil capacity (each fork): 286 cm³ (10.1 Imp oz, 9.67 US oz)

Recommended oil: SAE 5W type SE motor oil or equivalent

10.   After filling, slowly pump the forks up and down to distribute the oil.

11.   Inspect the O-ring on the cap bolt. Replace if damaged.

1. O-ring

12. Reinstall the cap bolt and tighten the pinch bolt.

Tightening torque: Cap bolt: 23 Nm (2.3 mkg, 17 ft-lb) Pinch bolt: 23 Nm (2.3 mkg, 17 ft lb)

13. Fill the fork with air using an air pump or pressurized air supply. Refer to "Front fork and rear shock absorber adjustment" for proper air pressure adjusting.

Maximum air pressure:  118 kPa (1.2 kg/cm², 17.1 psi) Do not exceed this amount.

Since the right and left front forks are connected by one air hose, there is only one valve where the air pressure is measured and adjusted.

Front fork and rear shock absorber adjustment

Front fork:

1. Elevate the front wheel by placing the motorcycle on the centerstand.

NOTE: When checking and adjusting the air pressure, there should be no weight on the front end of the motorcycle.

2.      Remove the valve cap from left fork.

3.      Using the air check gauge, check and adjust the air pressure.

If the air pressure is increased, the suspension becomes stiffer and if decreased, it becomes softer.

1. Air gauge

To increase: Use an air pump or pressurized air supply To decrease: Release the air by pushing the valve.

NOTE:

An optional air check gauge is available. Please ask a nearby Yamaha dealer. P/No. 2X4-2811A-00.

Air pressure:

39.2 kPa (0.4 kg/cm², 5.7 psi) Maximum air pressure:

118 kPa (1.2 kg/cm², 17.1 psi) Minimum air pressure: Zero

CAUTION: Never exceed the maximum pressure, or oil seal damage may occur.

4. Install the valve cap securely.

Rear shock absorber:

The rear shock absorber of this model features a spring seat, which is a combined spring preload and damping adjuster. Normal adjustment can be made by turning this spring seat; whereas damping adjustment only can be made by the damping adjuster.

CAUTION: Before adjustment, make sure of the following:

1.      Turn in the damping adjuster fully. Then turn it back until its red painted slit aligns with the pointer "▼" on the spring cover.

2.      For alignment in the absence of the red paint, turn the damping adjuster 6 clicks back from the fully turned-in position.

1. Spring seat adjustment

To increase the preload, turn the spring seat clockwise. To decrease the preload, turn the spring seat counterclockwise.

NOTE: When adjusting, use the special wrench which is included in the owner's tool kit

1. Spring seat

2. Damping adjustment

To increase the damping, turn the adjuster clockwise. To decrease the damping, turn the adjuster counterclockwise.

Standard position:

6 clicks turns out (or red mark) Minimum 12 clicks turns out Maximum 1 clicks turn out

NOTE: Make adjustment in less than one full turn of the adjuster.

1. Damping adjuster

Recommended combinations of the front fork and the rear shock absorber settings.

Use this table as guidance to meet specific riding and motorcycle load conditions.

* Each numeral shows the damping value which can be set when the pointer is aligned with the individual slit in the spring seat. The damping adjuster may be further turned for a softer or a harder damping; in each of the above settings, it is recommended that the damping be adjusted by one (1) or two (2) clicks on the softer side and one (1) click on the harder side.

Anti-dive adjustment

NOTE: Yamaha made a serious error in the original owner's manual regarding the anti-dive adjustment on the 900RK (essentially had it backwards). This is the corrected information, as per the September 1, 1983 TSB:

1. Remove the rubber cap from the bottom of the anti-dive unit.

1. Rubber cap

2.      Look at the head of the adjusting bolt through the slots in the bottom of the anti-dive unit. In the standard position, two lines will be visible on the adjusting bolt head. Consult the fork adjustment chart below to determine the proper setting.

3.      To decrease the anti-dive effect turn the adjusting bolt clockwise until the first line appears level to the top of the machined slot(s).

CAUTION: When the first line appears in the machined slot(s), the adjusting bolt will bottom in the anti-dive unit and a resistance will be felt. Do not attempt to turn the adjusting bolt beyond this point or the anti-dive unit will be damaged.

4. To increase the anti-dive effect, turn the adjusting bolt counterclockwise.

5. Replace the rubber cap.

WARNING: The anti-dive settings must be the same on both anti-dive units. Hence, be sure to perform the above procedure on both anti-dive units.

Cam chain adjustment

This model has been equipped with the automatic cam chain tensioner. No adjustment is necessary.

Ignition timing check

1. Ignition timing is checked with a timing light by observing the position of the stationary pointer and the marks stamped on the timing plate.

2.      Connect the timing light to No. 1 (L.H.) spark plug lead.

3.      Start the engine and keep the engine speed as specified. Use a tachometer to check the engine speed.

Specified engine speed: 1,050 r/min

4. The stationary pointer should be within the limits of "["]" on the timing plate. If it exceeds the limits or does not steady, check the timing plate for tightness and/ or ignition system for damage. (See "CHAPTER 6. ELECTRICAL)

CAUTION:

Never bend the stationary pointer.

Air filter

1. Removal

a.    Remove the seat.

b.    Remove the left and right side covers.

c.    Remove the tool box.

d.    Lift and loosen the electric fitting housing box from the frame.

e.    Remove the air filter case cover by removing the four screws.

f. Pull out the element.

1. Air filter element

2. Cleaning method

Tap the element lightly to remove most of the dust and dirt; then blow out the remaining dirt with compressed air from the inner surface of the element. If element is damaged, replace it.

3.      Reassemble by reversing the removal procedure. Check whether the element is seated completely against the case.

4.      The air filter element should be cleaned at the specified intervals.

CAUTION:

The engine should never be run without the air cleaner element installed; excessive piston and/or cylinder wear may result.

Idle mixture setting

The idle mixture is set at the factory by the use of special equipment. No attempt should be made by the dealer to change this adjustment

Carburetor synchronization

The seat must be removed and the rear of the tank elevated to gain access to the vacuum connections and synchronizing screw.

NOTE:

The valve clearances must be set properly before synchronizing the carburetors.

NOTE:

The carburetors are numbered 1, 2, 3, and 4 from the left when viewed from astride the motorcycle.

1. Remove the vacuum pipe from the carburetor manifold (No. 3 cylinder) and turn the fuel cock to "PRI."

2. Remove the rubber caps from the No. 1, 2, and 4 carburetor manifolds.

1. Rubber cap

3. Remove either the left or right (but not both) blind plug at the end of the YICS (Yamaha Induction Control System) passage in the cylinder.

1 Blind plug

4.      Insert the YICS shut-off tool (special tool) fully and flip the locking lever.

5.      Connect each vacuum gauge hose to its proper carburetor.

1. Vacuum gauge

6.      Start the engine and allow it to warm up for a few minutes. The warm-up is complete when the engine responds normally to the throttle opening.

7.      Make sure the engine idle speed is 950 ~- 1,000 r/min. If it is not adjust the idle speed with the throttle stop screw.

NOTE:

With the YICS shut off tool fitted, the engine speed generally drops a little. Thus, continue with the following steps at an idle speed of 950 — 1,000 r/min.

8. Each gauge reading will indicate the same if the carburetors are synchronized. The No. 3 carburetor has no synchronizing screw, and the other carburetors are to be synchronized to it in order, one at a time. First, synchronize carburetor No. 1 to carburetor No. 2 by turning the No. 1 synchronizing screw until both gauges read the same.

Second, in the same way synchronize carburetor No. 4 to carburetor No. 3. Third, by adjusting No. 2 screw, watch No. 3 carburetor reading. No. 1 and No. 2 carburetors will both change to match No. 3 carburetor.

9. Remove the YICS shut-off tool and reinstall the blind plug.

Tightening torque:

22 Nm (2.2 mkg, 16 ft-lb)

10. Check the idle speed. Adjust if necessary.

Idle speed adjustment

NOTE:

Carburetors must be synchronized before setting the final idle speed. The idle speed adjustment is made by turning only one throttle stop screw.

1.      The engine must be warmed up, before setting the idle speed.

2.      Set the engine idle speed by turning the throttle stop screw in (to increase engine speed) or out (to decrease engine speed).

Standard idle speed: 1,100 r/min

1. Throttle stop screw

Engine oil level measurement

1.      Place the motorcycle on its centerstand. Warm up the engine for several minutes.

NOTE:

Be sure the motorcycle is positioned straight up when checking the oil level; a slight tilt toward the side can produce false readings.

2.      With the engine stopped, check the oil level through the level window located at the lower part of the right side crankcase cover.

NOTE:

Wait a few minutes until the oil level settles before checking.

1. Level window 2. Maximum mark 3. Minimum mark

3. The oil level should be between maximum level and minimum marks. If the level is lower, add sufficient oil to raise it to the proper level.

Engine oil and oil filter replacement

1.      Start the engine and stop it after a few minutes of warm-up.

2.      Place an oil pan under the engine and remove the oil filler cap.

3.      Remove the drain plug and drain the oil.

4.      Remove the #2 exhaust pipe.

5.      Remove the oil filter bolt and filter element.

1. Drain plug

1. Oil filter cover

6. Reinstall the drain plug (make sure it is tight).

Drain plug torque: 43 Nm (4.3 m-kg, 31 ft lb)

7. Install the new oil filter element new CD-ring and filter cover; tighten the oil filter bolt.

Oil filter bolt torque:

15 Nm (1.5 m-kg, 11 ft-lb)

NOTE:

Make sure the O-ring is positioned properly.

8. Install the #2 exhaust pipe.

Tightening torque: 8 Nm (0.8 m-kg, 5.8 ft-lb)

9. Add oil through the oil filler hole.

CAUTION:

Take care not to allow foreign material to enter the crankcase.

10. After replacement of the engine oil, and/ or oil filter, be sure to check for oil leakage. The oil level indicator light should go off after the oil is filled.

CAUTION:

If the indicator light flickers or remains on, the oil level switch may be damaged. Refer to "CHAPTER 6" for corrective action.

Final gear oil level measurement

1.      Place the motorcycle on a level place and place it on the centerstand. The engine should be cool (at atmospheric temperature).

2.      Remove the oil filler cap and check the oil level whether it is to the hole brim. If it is not up to this level, replenish oil.

1. Final gear oil 2. Correct oil level

CAUTION:

Take care not to allow foreign material to enter the final gear case.

Final gear oil replacement

1.      Place an oil pan under the final gear case.

2.      Remove the final gear oil filler cap and the drain plug, and drain the oil.

1. Final gear drain plug

3.      Reinstall and tighten the final gear drain plug.

4.      Fill the gear case to the specified level.

Oil capacity:

Final gear case:

0.2 L (0.18 Imp qt, 0.21 US qt) Recommended oil:

SAE 80 API "GL-4" Hypoid gear oil If desired, an SAE 80W90 hypoid gear oil may be used for all conditions.

5. Reinstall the filler cap securely.

Compression pressure measurement

Insufficient compression pressure will result in performance loss and may indicate leaking valves or worn or damaged piston rings.

Procedure:

1.      Make sure the valve clearance is correct

2.     Warm up the engine 2—3 minutes. Stop the engine.

3.      Remove the all spark plugs.

4.      Install a compression check gauge.

5. Turn over the engine with the electric starter (make sure the battery is fully charged) with the throttle wide open until the pressure indicated on the gauge does not increase further.

Compression pressure (at sea level): Standard

981 kPa (10 kg/cm², 142 psi) Minimum

785 kPa (8 kg/cm², 114 psi) Maximum

1,177 kPa (12 kg/cm², 171 psi)

WARNING:

When cranking the engine, ground the removal spark plug leads to prevent sparking.

1. Compression gauge

6.      If the pressure is too low, squirt a few drops of oil into the cylinder being measured. Measure compression again. If there is a higher reading than before (without oil), the piston rings may be worn or damaged. If the pressure remains the same after measuring with the oil, either or both the rings and valves may be the cause.

7.      Check each cylinder. Compression pressure should not vary more than 98.1 kPa (1 kg/cm², 14 psi) from one cylinder to any other cylinder.

NOTE:

Valve clearance must be measured with the engine and at room temperature.

1. Remove the seat and remove the fuel tank holding clip and retainer.

1. Clip 2. Retainer

2.      Remove the starter (CHOKE) wire and spark plug leads.

1. Starter (CHOKE) wire

3.      Remove the cylinder head cover and left crankcase cover (pick-up base cover). Care should be taken to not scratch or damage the gasket sealing surfaces.

4.      Turn the crankshaft with the nut on the left end of the crankshaft to turn the cams. The proper position of the cam when measuring the valve clearance is with the cam lobe directly opposite the valve lifter.

5.      Insert a feeler gauge between the valve lifter and the camshaft base circle.

Valve clearance adjustment

Valve clearance is adjusted by replacing the adjusting pad on the top of the valve lifter. Adjusting pads are available in 25 thicknesses ranging from No. 200 (2.00 mm) to No. 320 (3.20 mm) in steps of 0.05 mm. The thickness of each pad is marked on the pad face that contacts the valve lifter (not the cam). Adjustment of the valve clearance is accomplished as follows:

1.      Determine valve clearance (feeler gauge measurement.)

2.      Remove adjusting pad and note number.

3.      Select proper pad from appropriate chart (intake or exhaust chart).

4.      Install new pad andcheck installed clearance.

Pad selection procedure

1.      Measure valve clearance. If clearance is incorrect record the measured amount of clearance. This must be measured carefully.

2.      There is a slot in the valve lifter. This slot must be positioned opposite the blade of the tappet adjusting tool before the tools is installed.

3.      Turn the cam until the lobe fully depresses the valve lifter and opens the valve. Install the tappet adjusting tool as shown to hold the lifter in this depressed position.

NOTE:

The tappet adjusting tool is fastened to the cylinder head securely using an alien screw. Make sure that the tool contacts the lifter only, and not the pad.

CAUTION:

If the cam lobe touches the tappet adjusting tool, the stress may fracture the cylinder head. DO NOT ALLOW THE CAM LOBE TO CONTACT THE TAPPET ADJUSTING TOOL.

1. Tappet adjusting tool

4. Carefully rotate the cam so that the pad can be removed. To avoid cam touching the adjusting tool, turn cams as follows: (view from left side of the motorcycle)

Intake: Carefully rotate CLOCKWISE. Exhaust: Carefully rotate COUNTERCLOCKWISE.

5. Remove the pad from the lifter. There is a slot in the lifter. Use a small screwdriver or other blade and tweezers or a magnetic rod to remove the pad. Note the number on the pad.

1 Adjusting pad

6  Proper pad selection is made as follows:

Chart lookup method:

Refer to the appropriate chart for exhaust or intake valves:

0.11 to 0.15mm required clearance (Intake side) chart

0.15 to 0.20mm required clearance (Exhaust side) chart

a.   Find number of original (installed) pad number on chart. Read down on chart.

b.   Find measured valve clearance (from step 1) on chart. Read across.

c.   At the intersection of installed pad number (down) and measured clearance (across) is a new pad number.

EXAMPLE:

Intake valve, installed pad: No. 250 (read down)
Measured clearance:0.32 mm (read across)
New pad number: No. 270(intersection of down & across)

Alternate shim calculation method:

Since all shims come in .05mm (.002") increments, you can quickly calculate the required size without a chart.

If the measured clearance is within 0.05mm (0.002") of the required clearance, then no change is needed.

If the measured clearance greater than 0.05mm (0.002") but 0.10mm (0.004") or less different than the required clearance then the next size shim is required.

If the measured clearance greater than 0.10mm (0.004") but 0.15mm (0.006") or less different than the required clearance then the next size shim is required.

Clearances that are too small require thinner shims. Clearances that are too large require thicker shims.

Example: Required exhaust valve clearance is 0.16~0.20mm. Measured clearance is 0.12mm (gap too small). Installed shim is Y270. Required shim is one size thinner: Y265.

NOTE:

The new pad number is to be used as a guide only. Verify the correctness of this choice in the following step(s).

7.      Install the new pad in the lifter. Install the pad with the number down.

8.      Remove tappet adjusting tool.

9.      Turn crankshaft to rotate cam several rotations. This will set the pad in the lifter.

10.   Check valve clearance (step 3). If clearance is incorrect, repeat preceding steps until proper clearance is obtained.

11.   Inspect head cover gasket. If bent or torn, replace gasket.

12.   Reinstall removed parts in reverse order.

Pick-up coil assembly

1. Remove the alien bolt that holds the timing plate.

2. Remove the pick-up coil securing screws and remove the pick-up coil assembly.

Shifter

1. Remove the change pedal.

2.      Remove the left crankcase cover.

3.      Remove the shift lever assembly and shift shaft assembly.

1. Shift lever assembly 2. Shift shaft assembly

4. Remove the middle gear case oil level maintaining plug.

Starter motor and generator

1. Remove the starter motor securing bolts and remove the motor assembly.

2. Remove the generator cover and stator coil assembly.

3. Install the rotor holding tool (special tool) on the rotor as shown and remove the rotor holding bolt.

1 Rotor holding tool

4. Insert the holding tool as shown and insert the rotor puller adapter (special tool) into the rotor shaft and screw in the rotor puller (special tool). Remove the rotor.

1. Rotor puller adapter

1. Rotor puller

Clutch

1. Remove right crankcase cover.

2. Release the tension evenly on the 6 mm bolts and remove the clutch pressure plate and clutch springs.

3.      Remove the friction plates and clutch plates.

4.      Straighten the lock washer tab. Use the clutch boss holder (special tool) to hold the clutch boss and remove the lock nut and lock washer.

1. Clutch boss holder

5. Remove the clutch boss and spacer.

6. Screw in a suitable length of 6 mm bolt into the one of the threaded holes on the collar and pull out the collar and needle bearing from the primary driven gear.

1. Collar 2. Pull

7. Remove the primary driven gear assembly and oil pump drive sprocket

8. Remove the oil collector plate.

Oil pump removal and disassembly

1. Remove the strainer cover. Note the wire harness clip position.

2. Remove the oil pump secruing bolts and remove the sprocket cover and oil pump assembly.

CAUTION: Do not attempt to remove the strainer screen as it is permanently fitted onto the pump housing. If the pump housing and/or any parts of the pump are damaged, the pump assembly must be replaced with a new one.

3. Remove the oil pump driven sprocket.

4.      Remove the oil pump cover and rotor assembly.

5.      Remove the pressure relief valve, spring and plunger.

Middle gear

1. Remove the middle driven gear housing holding bolts.

2. Remove the middle driven gear housing assembly and shims.

NOTE: If it is difficult to remove housing assembly, loosen the two crankcase bolts located near the middle driven gear housing.

3. Remove "TORX" screws holding the middle drive gear assembly.

4. Remove the bearing retainers.

Crankcase disassembly

1. Remove the upper crankcase bolts, starting the highest numbered bolt. Turn over the engine and remove the lower crankcase bolts.

CRANKCASE TIGHTENING SEQUENCE

LOWER CASE

UPPER CASE

Tightening Torque

8 mm bolt: 24 Nm (2.4 mkg, 17 ft-lb) O .... 6 mm bolt: 12 Nm (1.2 mkg. 8.7 ft-lb)

Separate the lower case from the engine. Use a soft rubber hammer to carefully separate the crankcase.

Upper crankcase

1. Remove the middle drive gear and damper assqmbly.

2. Remove the transmission main shaft assembly.

3. Remove the A. C. G. shaft cover.

4. Remove the oil spray nozzle.

5. Carefully remove the A. C. G. shaft from the gear.

6. Remove the gear from the chain.

7. Straighten the lock washer tab and remove the bolt securing the starter idle gear shaft. Remove the shaft and starter idle gear.

8. Remove the crankshaft.

Lower crankcase

1.      Remove the dowel pin and "O-ring".

2.      Remove the shift fork guide bar and shift forks. The shift forks are identified by numbers cast on their sides.

3. Remove the bolt securing the shift cam locating pin and remove the stopper plate and locating pin.

1. Shift cam locating pin 2. Neutral switch

4.      Remove the neutral switch.

5.      Pull out the shift cam.

6.      Remove the driven shaft bearing cover holding screws and remove the bearing cover.

7. Remove the 5th wheel gear from the driven shaft and pull out the driven shaft assembly.

1. 5th wheel gear

Cylinder head and cylinder

1.      Remove the cylinder head cover.

2.      Remove the left crankcase cover (pickup coil cover).

3.      Remove the cam chain tensioner.

4. Use a 19 mm wrench on the timing plate flats to rotate the crankshaft counterclockwise until the engine is at Top Dead Centre.

CAUTION: Never use an alien wrench to rotate the crankshaft. Always use the 19 mm flats provided on the timing plate to rotate this engine.

5. Remove the four cam sprocket bolts.

6. Slip each sprocket off its mounting boss on the cam.

CAUTION: From this point on, do not rotate the cam shaft or valve damage may occur. On this, it is not necessary to break the cam chain. However, it can be broken if so desired. It is easier to disassemble the engine without separating the chain.

7. Remove the cam chain guide.

1. Cam cham guide

8. Remove the cam caps. Note the location ofthe cam caps as shown. Directional arrows are cast on each cap and point toward the clutch side.

9. Fasten safety wire to the cam chain to prevent its falling into the crankcase cavity.

Slide the camshafts and sprockets from under the chain and remove the camshafts and sprockets.

10. Remove the front cam chain guide.

1. Front cam chain guide

11.   Remove the spark plugs.

12.   Remove the cylinder head bolts and nuts in the numerical order as shown. Start by loosening each nut 1/2 turn until all of the nuts are loose. Remove the cylinder head.

13. Remove the front cylinder holding nut and remove the cylinder assembly. It may be necessary to tap the cylinder lightly to loosen it from the base gasket.

14. Remove the rear cam chain guide by loosening the holding bolt.

1. Hoiding bolt 2 Rear cam chain guide

Cylinder head disassembly

1. Remove the valve lifters and pads. Be careful not to scratch the lifter bodies or lifter bores in the cylinder head. Be very careful to identify each lifters position so that it may be returned to its original place.

1 Valve lifter 2. Adjusting pad

2. Mount the valve spring compressor on the head and depress each valve spring. Take out the retainer and valve spring with tweezers.

1. Valve spring compressor

3. Remove valves.

NOTE: Deburr any deformed valve stem end. Use an oil stone to smooth the stem end. This will help prevent damage to the valve guide during valve removal.

DEBURR VALVE STEM

4. Use a small box to hold the parts and identify the original position of each lifter and valve. Be very careful not to mix the location of these components.

Piston

1.      Make each piston to aid in reassembly.

2.      Place a clean towel or rag into the cranckcase to keep circlips and material from falling into the engine.

3.      Remove piston pin clips, piston pins, and pistons.

Cylinder head cover

Place head cover on a surface plate. There should be no warpage. Correct by re-surfacing as follows:

Place # 400 or # 600 grit wet sandpaper on surface plate and re-surface head cover using a figure-eight sanding pattern. Rotate head cover several times to avoid removing too much material from one side.

Cylinder head

1.      Using a rounded scraper, remove carbon deposits from combustion chamber. Take care to avoid damaging spark plug threads and valve seats. Do not use a sharp instrument. Avoid scratching the aluminum.

2.      Check the cylinder head warpage with a straight edge as shown.

The warpage should not exceed the specified limit, it necessary resurface. If the warpage exceeds allowable limit, the cylinder head should be replaced with a new one.

Cylinder head warpage: less than 0.03 mm (0.0012 in) Allowable limit: 0.25 mm (0.010 in)

Valve, valve guide, and valve seat

1. Check the valve face and the stem end for wear. If the valve face and/or the stem end are pitted or worn, regrind the valve with a valve refacer. Replace the valve if any dimension exceeds the specifications in the illustration.

INTAKE/EXHAUST VALVE

2. Valve stem wear must be measured and then combined with valve guide measurements to guide clearance. This clearance must be within tolerances. If it exceeds the maximum limit, then replace either or both valve and guide, as necessary.

3.      Valve stem end

Inspect the end of the valve stem. If the end appears to be ''mushroomed" or has a larger diameter than the rest of the stem, the valve, valve guide, and oil seal should be replaced.

4.      Turn valve on "V" blocks and measure the amount of stem runout with a dial gauge. If it exceeds the maximum limit, replace the valve.

Maximum valve stem runout: 0.03 mm (0.0012 in)

5. Valve guide and valve oil seal replacement

If oil leaks into the cylinder through a valve due to a worn valve guide, or if a valve is replaced, the valve guide should also be replaced.

NOTE: The valve oil seal should be replaced whenever a valve is removed or replaced.

a. Measure valve guide inside diameter with a small bore gauge. If it exceeds the limit replace with an oversize valve guide.

Guide diameter (I. D.): Limit: 7.10 mm (0.280 in)

b.    To ease guide removal and reinstallation, and to maintain the correct interference fit heat the head to 100 °C (212°F). Use an oven to avoid any possibility of head warpage due to uneven heating.

c.    Use the appropriate shouldered punch (special tool) to drive the old guide out and drive the new guide in.

NOTE: When a valve guide is replaced, the 0-ring should also be replaced.

1. Valve guide remover

1. Valve guide installer

d. After installing the valve guide, use the 7 mm reamer (special tool) to obtain the proper valve guide to valve stem clearance.

e. After installing the valve guide in the cylinder head, the valve seat must be recut. The valve should be lapped to the new seat.

6. Grinding the valve seat a. The valve seat is subject to severe wear. Whenever the valve is replaced or the valve face is re-surfaced (see CAUTION) the valve seat should be re-surfaced at a 45° angle. If a new valve guide has been installed the valve seat must be recut to guarantee complete sealing between the valve face and seat.

Remove just enough material to achieve a satisfactory seat.

CAUTION: If the vatve seat is obviously pitted or worn, it should be cleaned with a valve seat cutter. Use the 45° cutter, and when twisting the cutter, keep an even downward pressure to prevent chatter marks.

If cutting section "A" of the valve seat, use 30° cutter. If cutting section "B", use the 45° cutter. If cutting section "C", use 60° cutter. b. Measure valve seat width. Apply mechanic's bluing dye (such as Dykem) to the valve face and valve seat, apply a very small amount of fine grinding compound around the surface of the valve face insert the valve into position, and spin the valve quickly back and forth. Lift the valve, clean off all grinding compound, and check valve seat width. The valve seat and valve face will have removed bluing wherever they contacted each other. Measure the seat width with vernier calipers. It should measure approximately 0.9 — 1.1 mm (0.035 — 0.043 in). Also, the seat should be uniform in contact area. If valve seat width varies, or if pits still exist, further cutting will be necessary.

c. If the valve seat is uniform around the perimeter of the valve face, but is too wide or not centered on the valve face, it must be altered. Use either the 30°, 45° or 60° cutters to correct the improper seat location in the manner described below:

1) If the valve face shows that the valve seat is centered on the valve face, but too wide, then lightly use both the 30° and the 60° cutters to reduce the seat width to 0.9 —1.1 mm (0.035 —0.043 in).

2) If the seat shows to be in the middle of the valve face, but too narrow, use the 45° cutter until the width equals 0.9 ~~ 1.1 mm (0.035 —0.043 in).

1. Valve seat cutter

3)   If the seat is too narrow and right up near the valve margin, then first use the 30° cutter and then the 45° cutter to get the correct seat width.

4)    If the seat is too narrow and down near the bottom edge of the valve face, then first use the 60° cutter and then the 45° cutter.

7. Lapping the valve/valve seat assembly

a.    The valve/valve seat assembly should be lapped if neither the seat nor the valve face are severely worn.

b.    Apply a small amount of coarse lapping compound to valve face. Insert the valve into the head. Rotate the valve until the valve and valve seat are evenly polished. Clean off the coarse compound, then follow the same procedure with fine compound.

Continue lapping until the valve face shows a complete and smooth surface all the way around. Clean off the compound material. Apply bluing dye to the valve face and seat and rotate the valve face for full seat contact which is indicated by a grey surface all around the valve face where the bluing has been urbbed away.

c. Valve leakage check

After all work has been on the valve and valve seat, and all head parts have been assembled, check for proper valve/valve seat sealing by pouring solvent into each of the intake ports, then the exhaust ports. There should be no leakage past the seat. If fluid leaks, disassemble and continue to lap with fine lapping compound. Clean all parts thoroughly, reassemble and check again with solvent. Repeat this procedure as often as necessary to obtain a satisfactory seal.

Valve spring and lifters

1. Checking the valve springs

a.    This engine uses two springs of different sizes to prevent valve float or surging. The valve spring specifications show the basic value characteristics.

b.    Even though the spring is constructed of durable spring steel, it gradually loses some of it's tension. This is evidenced by a gradual shortening of free length. Use a vernier caliper to measure spring free length. If the free length of any spring has decreased more than 2 mm (0.080 in) from its specification replace it

c. Another symptom of a fatigued spring is insufficient spring pressure when compressed. This can be checked using a valve spring compression rate gauge. Test each spring individually. Place it in the gauge and compress the spring first to the specified compressed length with the valve closed (all spring specifications can be found in the previous section, Valve spring), then to the length with the valve open. Note the poundage indicated on the scale at each setting. Use this procedure with the outer springs, then the inner springs.

NOTE: All valve springs must be installed with larger pitch upward as shown.

2. Valve lifter a. Check each valve lifter for scratches or other damage. If the lifter is damaged in any way, the cylinder head surface in which it rides is probably also damaged. If the damage is severe, it may be necessary to replace both the lifter and the cylinder head.

NOTE: For proper valve lifter-to-head clearance, always install lifters on their original valves.

Camshafts, cam chain and cam sprockets

1. Camshaft

a.    The cam lobe metal surface may have a blue discoloration due to excessive friction. The metal surface could also start to flake off or become pitted.

b.    If any of the above wear conditions are readily visible, the camshaft should be replaced.

c.    Even though the cam lobe surface appears to be in satisfactory condition, the lobes should be measured with a micrometer. Cam lobe wear can occur without scarring the surface. If this wear exceeds a pre-determined amount, valve timing and lift are affected. Replace the camshaft if wear exceeds the limits.

d.    Install the camshaft on the cylinder head. Place a strip of Plastigage between camshaft and camshaft cap as illustrated (lengthwise along camshaft). Tighten the nuts with specified torque. Remove the camshaft cap and determine the clearance by measuring the width of the flattened Plastigage.

Cap nut tightening torque: 10 Nm (1.0 rrvkg, 7.2 ft lb)

NOTE: Do not turn camshaft when measuring clearance with plastigage.

Camshaft-to-cap clearance:

Standard: 0.020 — 0.054 mm

(0.0008 —0.0021 in) Maximum: 0.160 mm (0.006 in)

If the camshaft-to-cap clearance exceeds specification, measure camshaft bearing surface diameter.

Bearing surface diameter: Standard: 24.967 — 24.980 mm (0.9830 - 0.9835 in)

1)    If the camshaft diameter is less than specification, causing excessive clearance, replace the camshaft.

2)   If the camshaft is within specificaton and camshaft-to-cap clearance is excessive, replace the cylinder head.

2.     Cam chain

Except in cases of oil starvation, the cam chain wears very little. If the cam chain has stretched excessively and it is difficult to keep the proper cam chain tension, the chain should be replaced.

3.      Cam sprockets

Check cam sprockets for obvious wear.

4. Cam chain dampers and tensioner

Inspect the top cam chain damper (stopper guide) and two (2) vertical (slipper-type) dampers for excessive wear. Any that shows excessive wear should be replaced. Worn dampers may indicate an improperly adjusted or worn-out cam chain.

Cylinder

1.      Inspect the cylinder walls for scratches. If vertical scratches are evident, the cylinder wall should be rebored or the cylinder should be replaced.

2.      Measure cylinder wall wear as shown. If wear is excessive, compression pressure will decrease. Rebore the cylinder wall and replace the piston and piston rings. Cylinder wear should be measured at three depths with a cylinder bore gauge. (See illustation.)

If the cylinder wall is worn more than the wear limit, it should be rebored.

Piston and piston rings

1. Piston

a. Measure the outside diameter of the piston at the piston skirt. Measurement should be made at a point 7.8 mm (0.307 in) above the bottom edge of the piston. Place the micrometer at right angles to the piston pin.

b. Determine piston clearance as follows: Minimum bore measurement

-  Maximum piston measurement = Piston clearance

EXAMPLE:

67.00 mm (2.6378 in)

-  66.96 mm (2.6362 in) = 0.04 mm (0.0016 in)

Piston clearance

Piston clearance:

Standard: 0.030 — 0.050 mm

(0.0012 —0.0020 in) Service limit: 0.1 mm (0.0039 in)

c. Piston ring/ring groove fit must have correct clearance. If the piston and ring have already been used, the ring must be removed and the ring groove cleaned of carbon. The ring should be then reinstalled. Use a feeler gauge to measure the gap between the ring and the land.

2. Piston ring a. The oversize top and middle ring sizes are stamped on top of the ring.

b. The expander spacer of the bottom ring (oil control ring) is color-coded to identify sizes.

The color mark is painted on the expander spacer.

Run-out limit: 0.03 mm (0.0012 in)

c. Insert a ring into the cylinder, and push it approximately 20 mm (0.8 in) into the cylinder. Push the ring with the piston crown so the ring will be at a right angle to the cylinder bore. Measure the ring end gap with a feeler gauge. If the end gap exceeds tolerance, replace the whole set of rings.

NOTE:  The end gap on the expander spacer of the oil control ring is unmeasurable. If the oil control ring rails show excessive gap, all three components should be replaced.

Piston pin

1.      Apply a light film of oil to pin. Install in connecting rod small end. Check for play. There should be no noticeable vertical play. If play exists, check connecting rod small end for wear. Replace pin and connecting rod as required.

2.      The piston pin should have no noticeable free play in piston. If the piston pin is loose, replace the pin and/or the piston.

Crankshaft

1. Crankshaft run-out

Support the crankshaft at both ends on V-blocks. Measure the amount of crankshaft run-out on the main bearing journals with a dial gauge while rotating crankshaft.

If run-out exceeds limit, replace crankshaft.

2.      Inspection of bearings

Check the bearings. If the inner or outer surface is burned, flaked, rough, scratched or worn, the bearings should be replaced.

3.      Measuring main bearing oil clearance

a.    Clean all crankshaft and crankcase journal surfaces.

b.    Place upper crankcase half upside-down on a bench. Install bearing inserts into top crankcase.

c.    Install crankshaft into upper crankcase.

d.    Place Plastigage on crankshaft journal surface to be inspected.

NOTE: Do not move crankshaft until clearance check has been completed.

e. Install bearings into bottom crankcase. Carefully, place lower crankcase onto upper crankcase.

f. Install crankcase holding bolts 1 through 10. Tighten to full torque in torque sequence cast on crankcase.

Crankcase torque (8 mm bolt): 24 Nm (2.4 mkg, 17 ft-lb)

g. Remove bolts in reverse assembly order (10, 9, 8 ... etc.)

h. Carefully remove lower crankcase. Measure width of Plastigage on crankshaft journals to determine clearance.

Main bearing oil clearance: 0.040 — 0.064 mm (0.0016 -0.0025 in)

4. Crankshaft main bearing selection a. Numbers used to indicate crankshaft journal sizes are stamped on the L.H. crank web. The first five (5) are main bearing journal numbers, starting with the left journal. The four (4) rod bearing journal numbers follow in the same sequence.

The upper crankcase half is numbered 4, 5, or 6 as shown.

1. Main bearing numbers

b. The connecting rods are numbered 4 or 5. The numbers for rods are stamped with ink on the rod itself.

c. The proper bearing selection is made by subtracting the crankshaft journal number from the crankcase or rod size number. Use the color code to choose the proper bearing. EXAMPLE:

Rod No. (Minus) Journal No. = Bearing No.

5-2 = 3 No. 3 bearing is Brown. Use Brown bearing inserts.

" For crankshaft main bearing only.

d.    When assembling, apply a liberal coat of motor oil to all bearing surfaces.

NOTE:  When applying final torque to the rod caps, observe the following procedures.

e.    Apply molybdenum disulfide grease to connecting rod bolt threads. Apply tor-que evenly to both ends of the cap. While tightening, if a torque of 38 Nm (3.8 m kg, 27 ft-lb) or more is reached, DO NOT STOP tightening until final torque is reached. If tightening is interrupted between 35 Nm (3.5 mkg, 25ft-lb) and 41 Nm (4.1 nrvkg. 30 ft-lb), loosen the nut to less than 30 Nm (3.0 nrvkg, 22 ft-lb) and start again. Tighten to full torque specification without pausing.

Rod bearing oil clearance: 0.016 — 0.040 mm (0.0006 —0.0016 in)

Oil pump

1. Check the clearance between housing and outer rotor.

Standard clearance: 0.03 — 0.09 mm (0.0012 — 0.0035 in)

2. Check the clearance between outer rotor and inner rotor.

Standard clearance: 0.03 — 0.08 mm (0.0012 — 0.0031 in)

3. Check the plunger for scratches and wear.

Clutch

1. Clutch housing

a.    Check the dogs on the clutch housing. Look for cracks and signs of galling on edges. If damage is moderate, deburr. If severe, replace the clutch housing.

NOTE: Galling on the friction plate dogs of the clutch housing will cause erratic clutch operation.

b.    Check the clutch housing bearing for damage. If damaged replace bearing.

2. Clutch boss

a.    The clutch boss contains a built-in damper beneath the first clutch plate (clutch plate 2). It is not normally necessary to remove the circlip and disassemble the built-in damper unless there is serious clutch chattering.

b.    Check splines on clutch boss for galling. If damage is slight to moderate, deburr; if it is severe, replace clutch boss.

NOTE: Galling on clutch plate splines will cause erratic operation.

3. Friction and clutch plates

Check clutch steel plates and friction plates for heat damage. Measure friction plate thickness at 3 or 4 points. Check each clutch plate for signs of heat damage and warpage. Place on surface plate (plate glass is acceptable) and use feeler gauge as illustrated. If warpage exceeds tolerance, replace.

NOTE: For optimum performance, if any friction or clutch plate requires replacement it is advisable to replace the entire set.

4. Clutch actuating mechanism

a.    Check the pull rod rack gear teeth for wear and damage, replace if damaged.

b.    Check the pull rod thrust bearing for damage, replace if damaged.

c.    Check the clutch lever shaft pinion gear teeth for damage, replace if damaged.

1 Plate washer 2. Thrust bearing 3. Pull rod

5. Clutch springs

Measure the clutch spring free length. Replace the springs as a set if any is less than minimum free length.

Clutch spring minimum length: 43.0 mm (1.69 in)

Transmission

1. Inspect each shift fork for signs of galling on gear contact surfaces. Check for bending. Make sure each fork slides freely on its guide bar.

2.      Roll the guide bar across a surface place. If the bar is bent, replace.

3.      Check the shift cam grooves for signs of wear or damage. If any profile has excessive wear and/or damage, replace cam.

4. Check the cam followers on each shift fork for wear. Check the ends that ride in the grooves in the shift cam. If they are worn or damaged, replace the shift forks.

5.      Check shift cam dowel pins and side plate for looseness, damage or wear. Replace as required.

6.      Check the shift cam stopper plate and circlip and stopper for wear. Replace as required.

7.      Check the transmission shafts using a centering device and dial gauge. If any shaft is bent beyond specified limit, replace shaft.

Maximum run-out: 0.08 mm (0.0031 in)

8.      Carefully inspect each gear. Look for signs of obvious heat damage (blue discoloration). Check the gear teeth for signs of pitting, galling or other extreme wear. Replace as required.

9.      Check to see that each gear moves freely on its shaft

10.   Check to see that all washers and clips are properly installed and undamaged. Replace bent or loose clips and bent washers.

11.   Check to see that each gear properly engages its counterpart on the shaft. Check the mating dogs for rounded edges, cracks, or missing portions. Replace as required.

Starter drives

1. Electric starter clutch and gears

a.    Check the surface of the idle gear for pitting or other damage. If severe, replace the gear.

b.    Check the spring caps and the springs for deformation or damage. If severe, replace as necessary.

c.    Check the starter clutch bolts (alien screw) for looseness. If loose, remove the bolts and replace with new bolts. Apply a thread locking compound such as "LOCTITE" to threads and tighten to specified torque. Stake over the end of the bolts.

Starter clutch bolt torque: 25 Nm (2.5 m-kg, 18 ft lb)

d.    Check the "HY-VO" chain for damage and wear, replace if damaged.

e.    Check the "HY-VO" chain guide for damage, replace if damaged.

Crankcases and strainer cover

I. Check crankcase for cracks or other

damage. I. Clean all oil passages and blow out with

compressed air.

3. Strainer cover: Apply a thread locking compound such as "LOCTITE" to strainer cover bolts during reassembly.

Bearing and oil seals

1.      After cleaning and lubricating bearings, rotate inner race with a finger. If rough spots are felt, replace the bearing.

NOTE: Bearings are most easily removed or installed if the housings are first heated to approximately 95° - 125°C (200° - 250°F). Bring the case up to proper temperature slowly. Use an oven to avoid distortion.

2.      Check oil seal lips for damage and wear. Replace as required.

Middle gear

1. Damper disassembly

NOTE: Disassembly of the middle gear damper requires the damper compressor (special tool) and a hydraulic press.

a. Place the middle drive shaft in a press with the damper compressor (special tool) in place as shown.

1.  Damper compressor 2. Press

b.    Press the damper spring and remove the spring retainers.

c.    Remove the spring seat, spring, and damper cams from the drive shaft.

2.      Inspection

a. Inspect the damper cam surfaces. Check for smooth cam action and excessive wear on the cam surface. If cam surface is severely worn, replace damper assembly.

b.    Inspect the damper spring for fatigue, wear and damage. Replace as necessary.

c.    Check bearing movement for damage to balls, rough spots, bearing looseness. Inspect gear teeth. If any gear tooth and/ or bearing are damaged, the gear set and/or bearing must be replaced.

3. Middle drive/driven shaft bearing removal

CAUTION: The following procedures should be performed only if the bearing or gear is to be replaced.

a. Middle drive gear

1)      Bend down the lock washer of the nut with a suitable center punch.

2)     Support the middle drive shaft in a vise securely.

Remove the drive pinion holding nut. Then, remove the drive pinion and bearing.

b. Middle driven gear

1) Support the drive flange in a vise securely. Remove the flange holding nut.

CAUTION: This holding nut has been locked with a thread locking compound, when reinstalling do not forget to apply a thread locking compound such as "LOCTITE" and punch.

2) Remove the drive flange from the driven shaft.

NOTE: Driven gear shaft bearing should be replaced together with a bearing housing.

Middle gear reassembly

a. Middle drive gear bearing and damper

1) Install the bearing onto the drive pinion and secure it with a new lock nut.

Tightening torque:

110 Nm (11.0 rrvkg, 80 ft lb)

2) Stake the lock washer of the nut to the slot on the drive pinion.

3)     Install the driven damper cam onto the drive pinion shaft with the cam lobes positioned 90° from the row of shaft oil holes. Positioning tolerance is ± 1 spline (15°) from the 90° position.

4)      Install the drive damper cams, spring, spring seat, and retainers using a press and the damper compressor.

1. Oil hole

b. Middle driven gear

1) Install the new bearing housing assembly onto the driven pinion shaft

CAUTION: Do not press the bearing outer race. Always press the inner race with care when installing.

2) Install the drive flange and new "0-ring" onto the driven gear shaft. Apply a thread locking compound such as "LOCTITE" tothe shaft threads and tighten the nut to the specified torque.

Tightening torque:

110Nm (11.0 m-kg, 80 ft lb)

3)      Stake the nut with a center punch to lock as shown.

4)      Install the new "O-ring" onto the bearing housing.

CRANKSHAFT/PISTON

. WHEN INSTALLING THE CONNECTING ROD. BE SURE THAT THE SECURING NUTS ARE ON TOP.

Engine assembly

1. Upper crankcase a. Install the connecting rods onto the crankshaft with the proper connecting rod bearings and apply molybedenum disulfide grease to the bolt threads. Apply torque evenly to both ends of the cap.

CAUTION: While tightening, if a torque of 38 Nm (3.8 mkg, 27 ft-lb) or more is reached, DO NOT STOP tightening until final torque is reached.

If tightening is interrupted between 35 Nm (3.5 mkg, 25 ft-lb) and 41 Nm (4.1 mkg, 30 ft-lb), loosen the nut to less than 30 Nm (3.0 mkg, 22 ft-lb) and start again. Tighten to full torque specification without pausing.

CAUTION: When installing the connecting rod, be sure that the securing nuts are on top. Otherwise, engine damage will result.

Rod cap torque: 38 Nm (3.8 mkg, 27 ft-lb)

b. Install the proper crankshaft main bearings into the crankcase and place the crankshaft. Oil the bearings liberaly.

NOTE: Do not forget to install the crankshaft oil seal (L.H.), blind plug (R.H.), "HY-VO" chain and cam chain on the crankshaft before installing. Also, install the chain guide into upper crankcase if removed.

c. Install the starter idle gear, shaft, stopper plate, and new lock plate. Tighten the bolt securely and bend the lock tabs along the bolt flats.

Tightening torque:

10 Nm (1.0 mkg, 7.2 ft-lb)

1, Lock washer

d. Put the starter clutch and sprocket assembly in the "HY-VO" chain and lay it into the crankcase.

e. Install the A.C.G. Generator shaft into the starter clutch assembly.

f. Install the "HY-VO" chain oil spray nozzle. The locating pin on the nozzle should be placed into the crankcase locating slot. Do not forget to install the new "O-ring" onto the nozzle.

1. O-ring

g. Install the new "O-ring" onto the bearing housing and install it with the panhead screw.

h. Install the transmission main axle assembly on the upper crankcase. Point the bearing locating pin toward the crankshaft and lay it on the case.

1. Bearing locating pin

i. Install the middle driven gear (without the middle drive pinion gear).

j. Install the middle driven gear shaft end bearing.

k. Install the dowel pin with "O-ring" into the crankcase.

1. O-ring

2. Lower crankcase a. Install the transmission drive axle assembly into the crankcase.

b. Install the 5th wheel gear and bearing onto the drive axle. Install the bearing cover. Be sure the "O-ring" is on the cover.

1. O-ring

c. Install the shift cam and secure it with the guide pin. Install the stopper plate and bolt and tighten securely.

d.    Install the neutral switch.

e.    Install the shift forks and guide bar. Each shift fork is identified by a number cast on its side. All the numbers should face the left side and numbered 1, 2, and 3 from left.

TRANSMISSION

3. Crankcase assembly a. Apply Yamaha bond #4 sealant or equivalent to the crankcase mating surface. Be very careful not to allow any sealant to come in contact with the oil gallery "O-ring" and crankshaft bearings. It is extremely important, however, that sealant be applied around the case stud holes. Apply sealant to within 2 — 3 mm (0.08 — 0.12 in) of the bearings.

CAUTION: Failure to apply sealant here will result in reduced oil pressure and possible crank seizure.

a. 2 — 3 mm (0.08 — 0.12 in) Do not apply sealant

b. The crankcases are assembled by placing the upper case half on the bench and lowering the lower case onto it.

NOTE: Be sure that shift fork No. 2 engages the groove in the 2nd pinion gear on the main axle.

CAUTION: Before installing and torquing the crankcase bolts, check to make sure the transmission is functioning properly by shifting it by hand with the shift cam.

c.    Start installation of the crankcase bolts with the center crankshaft area bolts. Place the two bolts without washers in the oil filter area.

d.    The crankcase bolts should be torqued in proper sequence. Refer to the tightening sequence in the illustration.

1. Engine ground wire

CRANKCASE TIGHTENING SEQUENCE LOWER CASE

UPPER CASE

8 mm bolt: 24 Nm (2.4 m kg. 1 7 ft lb) 6 mm bolt: 12 Nm (1.2 m kg. 8 7 ft-lb)

4. Oil pump and strainer cover

a.    Place the oil pump drive chain on the transmission main axle.

b.    Install the thrust plate onto the transmission main axle.

c.    Install the oil pump drive sprocket onto the main axle without the spacer collar and place the oil pump drive chain on its sprocket.

1. Oil pump drive sprocket

d. Place the drive chain on the oil pump driven sprocket and install the pump on the crankase. The "O-ring" should be installe properly.

e. Install the drive chain cover on the oil pump and secure with the 2 shouldered bolts and one normal 6 mm bolt.

Tlightening torque:

12 Nm (1.2 mkg, 8.7 ft-lb)

f. Install the strainer cover and torque the bolts to the specification.

Tightening torque:

7 Nm (0.7 m-kg, 5.1 ft lb)

1 Wire clamps

CLUTCH

5. Clutch assembly

a.    Insert the spacer coller into the oil pump drive sprocket.

b.    Install the primary driven gear (clutch housing) without the bearing and inner spacer.

CAUTION: Be sure that the oil pump drive gear tabs engage the clutch housing grooves on it's back or the tabs will be damaged when tightening the clutch boss securing nut.

1. Spacer collar

c. Install the primary driven gear bearing and inner spacer into the clutch housing.

1 Driven gear bearing 2. Inner spacer

d. Install the large thrust plate and clutch boss onto the main axle.

e. Install a new lock washer-and nut and tighten the nut to the specified torque. Use the clutch boss holder (special tool).

Tightening torque:

70 Nm (7.0 nrvkg, 50 ft-lb)

1. Clutch boss holder

f. Bend the lock washer tabs along the nut flats.

1. Lock tab

g. Install the clutch plates and friction plates alternately on the clutch boss, starting with a friction plate and ending with a friction plate.

h. Install the plate washer, thrust bearing, and clutch pull rod into the clutch pressure plate from inside.

1. Pull rod 2. Thrust bearing 3. Plate washer

i. Install the pressure plate assembly onto the clutch boss.

NOTE: Pressure plate has a dot on it which must line up with the dot on clutch boss.

j. Install the clutch springs and screws. Tighten the screws.

Clutch screw torque: 8 Nm (0.8 m-kg, 5.8 ft lb)

k. Install the oil collector plate.

1. Oil collector plate

I. Set the gear of the clutch pull rod on the pressure plate facing approximately 45° from horizontal toward the rear; set the clutch lever (if installed) on the right crankcase cover parallel to the gasket surface and install the cover to the crankcase. Do not forget to install two dowel pins.

m. If the clutch lever has been removed, install the lever return spring and lever on the shaft after installing the right crankcase cover. In this case make sure that the punch mark on the lever should align with the mark on the crankcase cover when pushing the lever towards the front by hand and then install the circlip.

1 Push

6. Middle gear (installation only, refer to page for the middle gear adjustment). a. Install the middle drive gear assembly with the proper size of shim(s) and secure it with the bearing retainers and new "TORX" screws.

Tightening torque: 25 Nm (2.5 mkg, 18 ft-lb)

b. Stake the screw heads to the dents on the bearing retainers with a center punch.

c. Install the driven gear assembly with the proper size of shims and secure it with the bolts. Apply a thread locking compound such as "LOCTITE" to the bolt threads.

Tightening torque:

25 Nm (2.5 mkg, 18 ft-lb)

1 Shims

d. Install the middle gear case half moon seal onto the crankcase.

1. Seal

7, Shifter assembly a. Install the shift shaft assembly with the stopper lever.

b. Install the shift lever assembly with the positioning spring is properly located on the stopper pin and the teeth should be set properly as shown.

c. Install the left crankcase cover (shifter cover) using a new gasket.

Tightening torque:

12Nm(1.2 mkg, 8.7 ft-lb)

8. A.C. generator a. Install the rotor onto the shaft and tighten the bolt using the rotor holding tool (special tool).

Tightening torque:

55 Nm (5.5 mkg, 40 ft-lb)

b. Install the stator coil assembly onto the crankcase and align the grooves on the stator core with the bolt holes on the crankcase.

c. Install the A.C. generator cover assembly and tighten the bolts to the specification. Do not forget to install the new gasket.

Tightening torque:

12 Nm (1.2 mkg, 8.7 ft-lb)

9. Starter motor

a.    Route the A.C. generator leads as shown.

b.    Install the starter motor and tighten the bolts to the specification.

Tightening torque: 7 Nm (0.7 mkg, 5.1 ft-lb)

NOTE: Be careful the "O-ring" is not damaged when installing the starter motor.

1 O-ring 2. A. C generator lead

10. Pick-up coil assembly

a.    Install the pick-up coil assembly onto the crankcase.

b.    Install the timing plate on the crankshaft and tighten the bolt to the specification.

NOTE: 

1)      Note that there is the locating pin on the crankshaft and the corresponding slot in the timing plate which must be aligned to install the timing plate.

2)     Make sure the wire harness clips are properly positioned.

11. Pistons and cylinder

a. Install the pistons on the rods. The arrow on the piston must point to the front of the engine.

NOTE: Before installing the piston pin clips, cover the crankcase with a clean rag so you will not accidentally drop the circlip into the crank-case. Always install new piston pin circlips.

b. Install the rear chain guide on its pivot. Tighten the holding bolt until it stops and then loosen 1/4 turn and then tighten the lock nut

1. Holding bolt 2. Rear cran guide

c. Install the new cylinder base gasket and dowel pins. Install the new "O-rings" to the right side dowel pins.

d. Set the crankshaft so that the all pistons are equal height and align the piston rings as shown.

CAUTION: Make sure the ends of the oil ring expanders are not overlapped.

NOTE: Manufacture's marks or numbers stamped on the rings are en the top side of the rings. Coat the pistons and rings well with oil.

e. Install the piston ring compressors (special tool) and piston bases (special tool). Four piston bases are required.

1. Piston bases 2. Piston ring compressors

f. Tie the cam chain with a piece of mechanic's wire and feed it through the chain opening. Carefully lower the cylinder onto the pistons. Remove the ring compressors and piston bases and repeat this procedure for pistons 1 and 4.

g. Install the cylinder securing nut (front side) and tighten it to the specification.

Tightening torque:

20 Nm (2.0 mkg, 14 ft lb)

h. Set the dial gauge on the No. 1 piston head center as shown to find the No. 1 piston top dead center and check whether the "T" mark on the timing plate and stationary pointer are aligned or not. If not, loosen the pointer securing screw and adjust.

CYLINDER HEAD

12. Cylinder head and cam shafts a. Install the new cylinder head gasket. Install the dowel pins and "O-rings". Locate the cam chain cavity cylinder seal with the tabs down.

b.    Install the cylinder head onto the cylinder. Pull the cam chain through the cylinder head as it is installed. Tie the cam chain so that it does not fall into the crankcase.

c.    Place the upper cylinder head nuts and washers in place. Follow the illustration for the proper tightening sequence. Torque all nuts in two stages and final torque the upper nuts to the specification.

Tightening torque:

32 Nm (3.2 mkg, 23 ft lb)

NOTE: Don't forget the lower nuts on the front and rear of the cylinder head. Torque to the specification.

Tightening torque: 20 Nm (2.0 mkg, 14ft-lb)

NOTE: Tighten the nuts in two stages, 1/2 torque value and then full torque value. Also lubricate the bolt threads with the engine oil to achieve proper torque values.

a. Copper washers

d.    Install the front cam chain guide being certain that it is in its holder down below.

e.    Rotate the crankshaft counterclockwise direction until the crankcase pointer and "T" mark on the timing plate are aligned.

f. With the cylinders No. 1 and 4 at the top dead center, slip the cam chain over the sprocket.

cj. Lubricate all cam caps and cam bearings surfaces liberally with oil.

h. Place the cam caps in their proper positions. Install the bolts only finger tight.

CAUTION: The cam caps must be tightened evenly or damage to the cylinder head, cam caps and cam will result. The spaces between the caps and cylinder head should be equal.

i. Torque the cam cap bolts in two stages and final torque to the specification.

Tightening torque:

10 Nm (1.0 m-kg, 7.2 ft-lb)

CAM CHAIN

13. Cam chain, cam sprockets and chain tensioner a. Rotate each cam shaft until the dot on the cam is aligned with the hole on the right cam cap.

CAUTION: Use extreme caution when rotating the cams. Two possible dangers exist. First, the wrench may contact the head and fracture it. Or second, a valve may become bent if the cam is turned the wrong way.

b. Carefully lift the cam chain from the exhaust cam sprocket and pull upward to remove any slack in the chain between the crankshaft and the exhaust cam sprocket. With all slack removed, place the chain back on the cam sprocket.

c. Grip each sprocket simultaneously and place them on the camshaft shoulders while continuing to keep tension on the chain from the crankshaft to the exhaust sprocket

CAUTION: Use only the special hardened shouldered bolts to install the cam chain sprockets to the cams.

Make sure the rollers of the cam chain are centered on both chain guides.

d. Rotate the sprockets slightly to align the bolt holes and insert one special bolt in each sprocket.

NOTE: Tighten only finger tight at this time.

e.    Install the center chain guide.

f.     Rotate the crankshaft counterclockwise and align the "C" mark on the timing plate with the timing pointer.

g. Remove the end plug and spring from the tensioner assembly.

h. Unlock the oneway cam by pushing it with your finger and push the tensioner rod into the tensioner body until it stops.

i. Install the tensioner to the cylinder and torque the bolts to the specification.

Tightening torque:

10 Nm (1.0 m-kg, 7.2 ft-lb)

j. Reinstall the spring and end plug with the gasket. Torque the end plug to the specification.

Tightening torque:

15 Nm (1.5 m-kg, 11 ft-lb)

k. Rotate the crankshaft more than one full revolution and align the "T" mark on the timing plate with the timing pointer. With the crankshaft at the "T" mark, the dots on the cams should be aligned with the raised holes on the right cam caps. If they are not aligned, disassemble the sprockets and chain tensioner and repeat above procedures.

I. Rotate the crankshaft and install the two remaining shoulder bolts into the cam sprockets. Torque all four sprocket holding bolts to the specification.

CAUTION: Be sure to attain the specified torque value to avoid the possibility of these bolts coming loose and causing serious damage to the engine.

Tightening torque:

20 Nm (2.0 m-kg, 14 ft-lb)

m. Adjust all valves as described in the "PERIODIC INSPECTIONS AND ADJUSTMENTS".

n. Install the cylinder head cover with a new gasket.

o. Install the left and right crankcase covers. The left crankcase cover (pickup coil cover) is required a gasket.

Middle gear servicing

1.      Disassembly

Refer to page 3-13 for disassembly.

2.      Inspection

Refer to page 3-29 for inspection.

3.      Gear lash check

NOTE: The middle gear lash can be checked only when the gears are installed in the crankcase.

a. Install the middle drive pinion holder (special tool) on the crankcase to hold the drive gear stationary during the lash measurement.

NOTE: Before installing the tool, loosen the holder bolt all the way out and after installation tighten this bolt as tight as necessary (finger tight is generally sufficient).

1. Middle drive pinion holder

b. Set the dial gauge to the middle drive flange as shown and gently rotate the drive flange back and forth. Note the lash measurement on the dial gauge.

Middle gear lash: 0.1 ~~ 0.2 mm (0.004 - 0.008 in)

a Middle gear lash

c. Check this engagement at 4 positions. Rotate the drive flange 90° each time and repeat the gear lash check.

NOTE: If the gear lash exceeds the specified limit and adjustment is necessary, the engine or swing arm should be removed from the motorcycle.

4. Gear lash adjustment a. Install the driven gear housing assembly into the crankcase leaving about a 2 mm (0.08 in) gap between the housing and crankcase and install the two bolts to the bearing housing 180° opposite to each other.

a. 2 mm (0.080 in)

b.    Install the middle drive shaft holder and dial gauge (refer to "Middle gear lash check").

c.    Slowly tighten the bolts alternately until the dial gauge lash measurement reaches 0.2 mm (0.008 in).

MIDDLE GEAR/DAMPER

a. Middle gear lash 0 2 mm (0.008 in)

d. Measure the gap between the driven gear bearing housing flange and the crankcase with a feeler gauge. This is the shim size required.

1 Feeler gauge

e. Install the proper sized shims as shown and tighten the driven gear housing to the specified torque. Recheck the gear lash, it should be within the specification, if not readjust the shims.

Gear lash: 0.1 — 0.2 mm

(0.004 — 0.008 in)

1. Shims

5. Drive gear positioning NOTE:

When the following part(s) is replaced with new one(s), drive gear positioning is necessary:

a.    Crankcase

b.    Middle gears

c.    Middle gear bearing housing

a. The shim thickness necessary for the drive gear positioning can be calculated from the infomations found on the upper crankcase and on the drive gear end.

b. To fined shim thickness "A" use the formula:

A = c - a - b

Where:

a = a numeral (usually a decimal number) printed on the shaft end as shown above and either added to or detracted from the nominal size "43".

b = a bearing thickness (considered constant)

c = a numeral (usually a decimal number) found on the upper crankcase half near the main bearing selection numbers and added to the nominal size "60".

Distance "b" = 16.94 mm

Example:

1)      If the shaft is marked +03....."a"

is 43.03 mm.

2)      "b" is 16.94 mm.

3)      If the crankcase is stamped "45" ....."c" is 60.45 mm.

A = c - a - b

A = 60.45 - 16.94 - 43.03

A = 0.48

Then the necessary shim thickness

is 0.48 mm. c. Shim size are supplied in the following thicknesses:

0.15 mm, 0.20 mm, 0.30 mm, 0.40 mm, and 0.50 mm.

Because the shims can only be selected in 0.05 mm increments the following chaft should be used when encountering last digits that are not 5 or zero(0):

Shim 0.30 mm + 0.15 mm

The following special tools are not available but can be constructed for the final gear disassembly and assembly:

PRESS TOOL NO. 1

PRESS TOOL NO. 2

GEAR CASE HOLDING TOOL

Troubleshooting

1. The following conditions may indicate damaged shaft drive components:

NOTE:  Damage areas A, B, and C above may be extremely difficult to diagnose. The symptoms are quite subtle and difficult to distinguish from normal motorcycle operating noise. If there is reason to believe component(s) are damaged, remove component(s) for specific inspection.

2. Inspection notes

a.    During coasting, accelerating or decelerating, the "rolling rumble" will increase with rear wheel speed, not engine or transmission gear speeds. However, such noise may also be due to wheel bearings.

b.    Noise that varies with acceleration and deceleration: Following incorrect reassembly, a condition of too-little gear lash may produce a whine during deceleration.

CAUTION: Too-little gear lash is extremely destructive to gear teeth. If a test ride following reassembly indicates this condition, stop riding immediately to minimize damage to gears.

c. A slight "thunk" must be distinguished from normal motorcycle operation. It will be most noticeable at low speed and could indicate broken gear teeth.

WARNING: If broken gear teeth are suspected, stop riding immediately. This condition could lead to locking-up of the shaft drive assembly and result in harm to a rider.

d. If the drive flange/universal joint bolts are slightly loose, a "clunk" may be felt when slowly taking off, or when changing from slow acceleration to slow decelration. At high speed this will result in vibration.

WARNING: Do not continue riding a motorcycle suspected of having loose flange/universal joint bolts. The components may break, causing injury to a rider.

3. Troubleshooting chart

Where Basic Conditions "a" and "b" above exist, consider the following chart:

4. Oil leak inspection

If a shaft drive component is suspected of leaking oil, first thoroughly clean the entire motorcycle. The spparent location of an oil leak on a dusty motorcycle may be misleading. Dry the motorcycle and apply a leak-localizing compound or a dry-powder spray that will limit the flow of any leaking oil. Operate the motorcycle prepared in this way for the distance necessary to precisely locate the leak. There are the possibilities that a component housing may have been damaged by road debris or an accident, or a gasket or seal may be cracked or broken. However, on new or nearly new motorcycle an apparent oil leak may be the result of a rust-preventive coating or excess assembly lubrication of seals. Always clean the motorcycle and recheck the suspected location of any apparent leakage.

5. Checking drained oil

Whenever a problem is suspected in either the middle or final gear assemblies, drain and inspect the oil. Metal particles on the drain plug or in the oil could indicate a bearing seizure or other problem in the component. However, a small amount of metal particles in the oil is normal.

Final gear removal

1.      Remove the rear axle and left shock absorber. Remove the rear wheel (see "REAR WHEEL" section in this chapter).

2.      Remove the 4 nuts holding the final drive unit to the swing arm.

3.      Remove the final gear assembly.

4.      Remove the circlips, plate washer and oil seal. Then pull out the drive shaft.

1. Circlip 2. Plate washer 3. Oil seal 4. Drive shaft

Gear lash check and adjustment

1.      Secure the gear case in a vice or other support.

2.      Remove the drain plug from the final gear case. Then, install a specified size of bolt (as shown) into the drain plug hole. Finger-tighten the bolt until it holds the ring gear.

NOTE:  The bolt should not be over tightened, finger tight is sufficient.

3. Install the final gear lash measurement tool on the gear coupling.

1. Gear lash measurement tool (Final gear)

4. Mount a dial gauge against the lash measurement tool at the scribed mark (60 mm (2.36 in) from the center of the shaft).

5. Use the special wrench to gently rotate the gear coupling back and forth. Note the lash measurement on the dial gauge.

Final gear lash: 0.25 — 0.50 mm (0.010 — 0.020 in) When using the measurement tool. 0.1 — 0.2 mm (0.004 — 0.008 in) Actual gear lash on the final gear teeth

1. Middle and final gear noising tool

6. If the gear lash exceeds the specified limits, adjust as follows.

a.    To reduce gear lash, increase the ring gear shim.

b.    To increase gear lash, reduce ring gear shim.

1. Ring gear shlim

c. If it is necessary to increase the ring gear shim by more than 0.1 mm (0.004 in) reduce the thrust washer thickness by 0.1 mm (0.004 in) for each 0.1 mm (0.004 in) of ring gear shim increase and if it is necessary to reduce shim by more than 0.1 mm (0.004 in), reverse above procedure.

Final gear disassembly

1.      Remove the nuts and bolts holding the bearing housing.

2.      Remove the ring gear assembly and thrust washer from the final gear case.

3. Remove the self-locking nut from drive pinion by using the holding tool (special tool) and remove the coupling.

1. Middle and final gear holding tool

4. Remove the drive pinion bearing retainer with the retainer remover (special tool).

CAUTION: The drive pinion bearing retainer nut is left hand threads. Turn the retainer nut clockwise to loosen.

1. Drive pinion bearing retainer remover

5. Remove the drive pinion and bearing with the slide hammer and adapter (special tool).

CAUTION: This drive pinion removal should be performed only if gearing replacement is necessary. Do not re-use bearings or races after removal.

1. Slide hammer 2. Crank installer adapter

6. Remove the guide coller, oil seal, and roller bearing from the main housing by using the press tool No. 1 (special tool) and a press. Use an appropriate supports for the main housing during this operation. The roller bearing may be reused if undamaged. Do not re-use oil seal.

7. Rear drive pinion roller bearing; removal of this bearing is difficult and seldom necessary. Heat the bare housing to 150°C (302°F). Use an appropriately shaped punch to remove the roller bearing outer race. Remove the inner race from the drive pinion-

Final gear reassembly

1. Install the new rear drive pinion roller bearing. Heat the bare bearing to 150°C (302°F) and use an appropriately adapter to install the roller bearing outer race. Install the inner race onto the drive pinion.

2. Using the press tool No. 2 (special tool) and a press, install the guide coller, new oil seal, and roller bearing into the main housing in that order.

NOTE: The removed roller bearing can be used if undamaged; however, we recommend replacement with a new one.

3. Final drive/ring gear positioning

NOTE: When the following part(s) is replaced with new one(s), gear positioning is necessary:

a.    Final gear

b.    Ring gear bearing housing

c.    Bearing(s)

a. The shim thickness "A" necessary for the drive pinion gear positioning can be calculated from the informations found on the final gear case and on the drive gear end.

To fined shim thickness "A" use the formula:

A = a - b

Where: a =a numeral (usually a decimal number) on the gear near the tooth and either added to or detracted from the nominal size "84". b =a numeral on the gear case appearing as a whole figure (ie. 83.50).

Example:

1)     If the pinion gear is marked "+01" ....: "a" is 84.01.

2)      If the gear case is marked "83.50".

A = 84.01 - 83.50

A = 0.51

Then the necessary shim thickness is 0.51 mm.

Shim sizes are supplied in the following thicknesses:

0.15 mm, 0.30 mm, 0.40 mm, 0.50 mm, 0.60 mm.

Because the shims can only be selected in 0.05 mm increments the following

chart should be used when encountering last digits that are not 5 or zero (0):

Shim thickness: 0.50 mm

b. The shim thickness "B" necessary for the ring gear positioning can be calculated from the informations found on the final gear case, ring gear, and bearing.

To find shim thickness "B" use the formula:

B = c + d-(e + f)

Where:

c = a numeral on the gear case appearing as a whole figure (ie. 45.52)

d = a numeral (usually a decimal number) on the outside of the ring gear bearing housing and added to the nominal size "3".

e = a numeral (usually a decimal number) on the inside of the ring gear and; either added to or detracted from the nominal size "35.40".

f = a bearing thickness (considered constant)

Distance "f" = 13.00 mm

Example:

1)      If the gear case is marked "45.52".

2)      If the ring gear bearing housing is marked "35"....."d" is 3.35.

3)     If the ring gear is marked "+01" .....

"e" is 35.40 + 0.01 = 35.41.

4)      "f" is 13.00.

B = c + d-(e + f)

B = 45.52 + 3.35 - (35.41 + 13.00)

8 = 48.87 - (48.41)

B = 0.46

Then the necessary shim thickness is 0.41 mm.

NOTE:  Use the chart for the drive pinion shim to select the ring gear shim size.

Shim thickness: 0.40 mm

4. Install the drive pinion gear with the proper size of shim(s) and secure it with the bearing retainer nut with the drive pinion bearing retainer remover (special tool).

NOTE: The bearing retainer nut is left hand threads;

turn the nut to counterclockwise to tighten.

Tightening torque: 110 Nm (11.0 mkg, 80 ftlb)

5. Install the ring gear assembly without the thrust washer. Adjust the gear lash (refer to "Gear lash check and adjustment").

6.      Place four pieces of "PLASTIGAGE" between the originally fitted thrust washer and ring gear.

7.      Install the gear case onto the ring gear assembly and tighten the nuts and bolts with the specified torque.

Tightening torque:

Bolt/Nut: 23 Nm (2.3 mkg, 17 ftlb)

NOTE:  Do not turn the drive pinion/ring gear when measuring clearance with "PLASTIGAGE".

8. Remove the ring gear assembly and determine the clearance by measuring the width of the flattened "PLASTIGAGE".

Ring gear thrust clearance:

0.1 - 0.2 mm (0.004 - 0.0078 in)

1. PLASTIGAGE

9. If the clearance exceeds the specification above, replace the thrust washer to obtain the proper clearance.

Removal

1.      Remove the rear wheel.

2.      Remove the final gear case assembly.

3.      Remove the drive shaft.

4.      To remove the universal joint, it is necessary to remove the swing arm. Remove the universal joint assembly.

Inspection

1. Drive shaft

Inspect the shaft splines for wear and/or damage. If excessive, replace the drive shaft

NOTE:  When installing the drive shaft lubricate splines with molybdenum disulfied grease.

2. Universal joint

a.    There should be no noticeable play in the universal joint bearings. If there is any play in the bearing, replace the universal joint assembly.

b.    Move the universal joint up and down and from side to side. The universal joint should move smoothly. Without tightness, binding or rough spots that could indicate damaged bearings. If damaged, replace the universal joint assembly.

Reinstallation

When installing the drive shaft and the universal joint reverse the removal procedure. Note the following points:

1.      Lubricate the shaft splines with molybdenum disulfied grease.

2.      Tighten the universal joint securing bolts and final gear case securing nuts with the specified torque:

Final gear case:

42 Nm (4.2 mkg, 30 ft lb) Universal joint:

44 Nm (4.4 mkg, 32 ft-lb)